Tech questions that don't fit above forums
Moderator: Team
mitch
Expert
Posts: 710 Joined: Fri May 11, 2012 8:38 am
Location:
Post
by mitch » Wed Oct 02, 2013 1:20 pm
Where is the best place to get the .500 round cbn insert holders.
Thanks
jred
Expert
Posts: 505 Joined: Sun Jun 11, 2006 12:14 am
Location: tucson arizona
Contact:
Post
by jred » Fri Oct 04, 2013 12:03 am
look in shop trader mag I bought some from the guy in tupalow miss I think they were about 90.00 each they worked good on my machine he has .375 and .500 single sided and double sided
mitch
Expert
Posts: 710 Joined: Fri May 11, 2012 8:38 am
Location:
Post
by mitch » Fri Oct 04, 2013 6:12 am
Where can I find that magazine.Is it online?
Thanks
resurrectionjoe
Pro
Posts: 234 Joined: Fri Sep 26, 2008 12:00 am
Location: Northeastern PA
Post
by resurrectionjoe » Fri Oct 04, 2013 7:55 pm
jred is refering to this company.
Quality Cutter Grinding
1915 Elvis Presley Drive
Tupelo, MS 38804 - map
Phone: (662) 844-9102
I also have bought cbn inserts from him.
mitch
Expert
Posts: 710 Joined: Fri May 11, 2012 8:38 am
Location:
Post
by mitch » Fri Oct 04, 2013 8:01 pm
Do you know if they have holders too.
Thanks
resurrectionjoe
Pro
Posts: 234 Joined: Fri Sep 26, 2008 12:00 am
Location: Northeastern PA
Post
by resurrectionjoe » Fri Oct 04, 2013 10:33 pm
mitch wrote: Do you know if they have holders too.
Thanks
They did not have holders when I purchased my inserts.
PHANTASM
Member
Posts: 120 Joined: Thu Aug 11, 2011 12:19 am
Location: minnesota
Post
by PHANTASM » Fri Oct 25, 2013 10:46 am
I FOUND SOME FOR 5PCS WAS 140 SHIPPED TO MY DOOR. THEY WORK AWESOME.
I get a 12ra on aluminum and 17 on cast iron/steel
mitch
Expert
Posts: 710 Joined: Fri May 11, 2012 8:38 am
Location:
Post
by mitch » Sun Oct 27, 2013 8:14 pm
What holder do you have
Thanks Mitch
ShaunK
New Member
Posts: 33 Joined: Sun Aug 02, 2009 8:53 pm
Location: New Castle, PA
Post
by ShaunK » Mon Nov 04, 2013 7:01 pm
PHANTASM wrote: I FOUND SOME FOR 5PCS WAS 140 SHIPPED TO MY DOOR. THEY WORK AWESOME.
I get a 12ra on aluminum and 17 on cast iron/steel
Where did you find the holders?
PHANTASM
Member
Posts: 120 Joined: Thu Aug 11, 2011 12:19 am
Location: minnesota
Post
by PHANTASM » Tue Nov 05, 2013 2:22 pm
I MADE MY OWN HOLDERS FOR A SM2000 VAN NORMAN RESURFACER. got rid of that stone and coolant mess. works very nice.
cost me about 45 for materials
mitch
Expert
Posts: 710 Joined: Fri May 11, 2012 8:38 am
Location:
Post
by mitch » Tue Nov 05, 2013 6:50 pm
Do you have any pictures that you could post
Thanks Mitch
PHANTASM
Member
Posts: 120 Joined: Thu Aug 11, 2011 12:19 am
Location: minnesota
Post
by PHANTASM » Tue Nov 26, 2013 10:25 am
pic
You do not have the required permissions to view the files attached to this post.
PHANTASM
Member
Posts: 120 Joined: Thu Aug 11, 2011 12:19 am
Location: minnesota
Post
by PHANTASM » Tue Nov 26, 2013 10:28 am
another
You do not have the required permissions to view the files attached to this post.
mitch
Expert
Posts: 710 Joined: Fri May 11, 2012 8:38 am
Location:
Post
by mitch » Sat Nov 30, 2013 9:13 am
Does it bolt in place of where the stone went .Can you send a pic of the whole wheel
Thanks Mitch
user-3597028
Post
by user-3597028 » Sun Dec 01, 2013 1:19 pm
PHANTASM wrote: pic
Which direction does your SM 2000 cut?
Mine spins clockwise from the bottom and cuts right to left.