Lots of parts

NOT ALLOWED: Selling or reselling in a retail manner.

Moderator: Team

Post Reply
In-Tech
Guru
Guru
Posts: 1510
Joined: Wed Apr 21, 2010 4:35 am

Lots of parts

Post by In-Tech » Fri Jan 17, 2014 2:38 pm

Hi Folks,
Cleaning up shop to free up some cash to buy other things I want :) . I think the prices are fair but any offers received via pm will be looked at. I'll email pictures upon request. All items are PLUS freight. I'm in central California.


14-71 Alcohol Kuhl std helix mag case with drive and pulleys(56/60 8mm) 6 passes since freshened by The Blower Shop and has their billet front cover. $2000

New Mahle pistons and rings, the expensive ones with the vertical gas ports 4.035 x 1.250ch 12 cc ASCS dome, 1.1/ 1.1/ 3mm . $800
Pistons Catalog number 0936914135, rings 4040ML-043 4.035 + .005

Whipple 1.6 L rear entry blower, excellent like new shape. $800

Vortech S-trim blower, less than 4 hours on it, went to T-trim, excellent shape. $800

Brodix -11 ASCS heads, fresh valve job and surface, new roller springs, was on alcohol. No porting. Complete but had T & D's therefore no studs/plates $1000

Holley Alcohol 750 List # 80535-1 Perfect shape $350

LA Enterprises Kryptonite SBC crankshaft. Ultralight scalloped design. 3.500" stroke STD/STD BW 1647 seems I remember it right at 40lbs $1000

2-sets of 16 Crower Aluminum Roller rockers SBC 1.5 ratio .150 offset in & ex. Perfect shape. Went to Jesel $200 set of 16

2-Erson Solid Roller SBC cams. .400" lobe 247/259 114LC Very easy on valvetrain, good street nitrous/blown or marine. Perfect shape $100 ea

New Painless wiring TBI harness #60101 $200

Rochester 17090304 36# injectors High impedance, just cleaned/flow tested 2 weeks ago $200 set of 8

Siemens 3102 57# low impedance injectors, will clean/flow test before shipment. $250 set of 8
Heat is energy, energy is horsepower...but you gotta control the heat.
-Carl

In-Tech
Guru
Guru
Posts: 1510
Joined: Wed Apr 21, 2010 4:35 am

Re: Lots of parts

Post by In-Tech » Mon Jan 20, 2014 9:33 pm

14-71 Sold
Heat is energy, energy is horsepower...but you gotta control the heat.
-Carl

r2dudes
New Member
New Member
Posts: 6
Joined: Mon Dec 24, 2007 4:23 pm

Re: Lots of parts

Post by r2dudes » Thu Jan 23, 2014 9:17 pm

sent you a PM

In-Tech
Guru
Guru
Posts: 1510
Joined: Wed Apr 21, 2010 4:35 am

Re: Lots of parts

Post by In-Tech » Fri Feb 07, 2014 3:23 pm

Painless TBI wiring harness sold. Thanks

Also, correction, the Mahle pistons have the lateral gas ports, NOT vertical. I just re-read the ad and noticed that, sot sure what I was thinking #-o
Heat is energy, energy is horsepower...but you gotta control the heat.
-Carl

In-Tech
Guru
Guru
Posts: 1510
Joined: Wed Apr 21, 2010 4:35 am

Re: Lots of parts

Post by In-Tech » Fri Feb 07, 2014 3:26 pm

In-Tech wrote:Painless TBI wiring harness sold. Thanks

Also, correction, the Mahle pistons have the lateral gas ports, NOT vertical. I just re-read the ad and noticed that, not sure what I was thinking #-o
Heat is energy, energy is horsepower...but you gotta control the heat.
-Carl

In-Tech
Guru
Guru
Posts: 1510
Joined: Wed Apr 21, 2010 4:35 am

Re: Lots of parts

Post by In-Tech » Wed Jun 18, 2014 2:00 am

Ttt
All injectors sold.
Heat is energy, energy is horsepower...but you gotta control the heat.
-Carl

paul8
New Member
New Member
Posts: 1
Joined: Sun Feb 05, 2017 3:33 am

Re: Lots of parts

Post by paul8 » Wed Jun 21, 2017 4:53 pm

Hi,
I found your older announcement with different parts. There were also Rochester injectors 17090304.
I am looking for few of them. DO you know cross reference and what is the fuel flow of these injectors?
Thank you!

In-Tech
Guru
Guru
Posts: 1510
Joined: Wed Apr 21, 2010 4:35 am

Re: Lots of parts

Post by In-Tech » Thu Jun 22, 2017 4:47 pm

That is the only part number I know for them. They are ~36lb @ 43psi and ~42lb @ 58psi
Heat is energy, energy is horsepower...but you gotta control the heat.
-Carl

Post Reply