New Edelbrock Victor Jr Heads with Full Portwork by Mondello
Posted: Fri Jan 23, 2015 3:00 am
$2,800 - New Edelbrock Victor Jr. heads for small block Chevy with full portwork by Mondello. Never bolted on an engine.
If interested, please send PM. I am located NW of Houston, Texas.
Will ship parts and split shipping cost within lower 48 states...... Payment by US Postal Money Order accepted.
If picking up parts locally, cash on receipt...... No checks, MOs nor credit cards if picking up locally.
All sales are final......
Description (priour to port work)......
http://www.edelbrock.com/automotive/mc/ ... r-sb.shtml
I had Mondello rework these 23 degree heads for a 427 stroker small block as an affordable alternative to 18 degree or 15 degree heads.
I asked Modello to port these heads so as to maximize flow at valve lifts below 0.550". I was looking for a flow rate for this engine of at least 300 cfm at that lift.
The specs Mondello gave me are as follows......
* Edelbrock Victor Jr. Aluminum Heads Fully Ported By Mondello Racing - 23 degree with standard valve spacing (no offset rockers required)
* 65cc Combustion Chambers, polished
* 2.08" intake X 1.60" exhaust valve sizes - Stainless Steel Pro-Flo with 5-angle valve job
* Intake Ports - 2.35" High X 1.40" Wide = 3.25 sq. in. cross section at port opening (allowing for rounded corners) - Pushrod pinch point measures 2.80 sq. in.
* Exhaust Ports - 1.65" High X 1.65" Wide = 2.68 sq. in. cross section at port opening (allowing for rounded corners)
* Dual Valve Springs Set @ 140 lb. seat pressure / 340 lb. open / cryogenic stress relieved
* P.C. Teflon Valve Guide Seals
Flow @ 28 in. (no pipe)
* LIFT INTAKE EXHAUST
0.100" 071.00 063.00
0.200" 145.00 113.00
0.300" 205.00 157.00
0.400" 260.00 190.00
0.500" 306.00 205.00
0.550" 313.00 211.00
0.600" 320.00 217.00
Best regards and thanks for your interest,
Harry
If interested, please send PM. I am located NW of Houston, Texas.
Will ship parts and split shipping cost within lower 48 states...... Payment by US Postal Money Order accepted.
If picking up parts locally, cash on receipt...... No checks, MOs nor credit cards if picking up locally.
All sales are final......
Description (priour to port work)......
http://www.edelbrock.com/automotive/mc/ ... r-sb.shtml
I had Mondello rework these 23 degree heads for a 427 stroker small block as an affordable alternative to 18 degree or 15 degree heads.
I asked Modello to port these heads so as to maximize flow at valve lifts below 0.550". I was looking for a flow rate for this engine of at least 300 cfm at that lift.
The specs Mondello gave me are as follows......
* Edelbrock Victor Jr. Aluminum Heads Fully Ported By Mondello Racing - 23 degree with standard valve spacing (no offset rockers required)
* 65cc Combustion Chambers, polished
* 2.08" intake X 1.60" exhaust valve sizes - Stainless Steel Pro-Flo with 5-angle valve job
* Intake Ports - 2.35" High X 1.40" Wide = 3.25 sq. in. cross section at port opening (allowing for rounded corners) - Pushrod pinch point measures 2.80 sq. in.
* Exhaust Ports - 1.65" High X 1.65" Wide = 2.68 sq. in. cross section at port opening (allowing for rounded corners)
* Dual Valve Springs Set @ 140 lb. seat pressure / 340 lb. open / cryogenic stress relieved
* P.C. Teflon Valve Guide Seals
Flow @ 28 in. (no pipe)
* LIFT INTAKE EXHAUST
0.100" 071.00 063.00
0.200" 145.00 113.00
0.300" 205.00 157.00
0.400" 260.00 190.00
0.500" 306.00 205.00
0.550" 313.00 211.00
0.600" 320.00 217.00
Best regards and thanks for your interest,
Harry