Compression ratio and engine life

General engine tech -- Drag Racing to Circle Track

Moderator: Team

The Badger
Member
Member
Posts: 78
Joined: Fri Jan 27, 2017 5:05 pm
Location: Rutherfordton NC

Compression ratio and engine life

Post by The Badger »

Have been pondering what the expected life expectancy of an engine is when ever you increase the CR. I've always been under the understanding that the rings would take more of a beating but what about the bearings? Say you went from 10:1 up to 12:1,how about 10:1 to 15:1? is there any way to estimate the drop in life of engine(taking out factor of detonation), maybe figure just an average percentage of what you expected before the CR change? Just one of those questions I can't seem to get any real answer for and figured why not ask the guys who have been doing this before I was born. Thanks for any insight.
pdq67
Guru
Guru
Posts: 9841
Joined: Thu Mar 04, 2010 8:05 pm
Location:

Re: Compression ratio and engine life

Post by pdq67 »

Good question and will be waiting for any AND all comments!

pdq67
joespanova
Expert
Expert
Posts: 876
Joined: Sat Dec 01, 2007 5:15 pm
Location: McDonough Ga.

Re: Compression ratio and engine life

Post by joespanova »

If you're building a high compression engine its safe to assume you'll be inside it more often anyway , assuming the intention is racing it.
So why would it matter , its not going to change anything.
modified wanna be
Joe-71
Pro
Pro
Posts: 297
Joined: Sat Apr 08, 2017 5:46 pm
Location:

Re: Compression ratio and engine life

Post by Joe-71 »

Not to diss your question, but diesel engines go hundreds of thousands of miles on same set of bearings. Cylinder preparation, proper seating of the rings, ring tension, oil control, fuel control, and proper servicing all come into play on mileage limitations. Fuel injection has really limited the fuel wash down of cylinder walls and associated ring wear and contamination of oil. Joe-71
Joe-71
David Redszus
Guru
Guru
Posts: 9633
Joined: Tue Nov 27, 2007 9:27 am
Location: Chicago
Contact:

Re: Compression ratio and engine life

Post by David Redszus »

In some engines, going from 9.0 to 9.5-1 compression ratio is grave cause for concern.
Yet my Mercedes runs 11.1-1 and is happy as a lark, even on regular gas.

Much depends on the design of the combustion chamber and the rest of the power train and thermal management.
User avatar
ptuomov
Guru
Guru
Posts: 3587
Joined: Fri Aug 07, 2009 3:52 am
Location:

Re: Compression ratio and engine life

Post by ptuomov »

Higher compression means higher cylinder pressures, both because of the higher compression directly and also because of faster burn around TDC. If the peak cylinder pressures are the limiting factor in reliability, then that’s an issue. For normally aspirated engines, it’s probably not an issue in many cases.
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
dirtracr5
Guru
Guru
Posts: 1494
Joined: Tue Mar 20, 2012 1:29 pm
Location:

Re: Compression ratio and engine life

Post by dirtracr5 »

Some Gm engines have compression ratios of 11.5 to 1. They have 100k mile warranties....
gnicholson
Pro
Pro
Posts: 482
Joined: Tue May 06, 2008 9:59 pm
Location: kansas city mo

Re: Compression ratio and engine life

Post by gnicholson »

You have to take cam timing into account also.its cylinder pressure vs crank angle
peejay
Guru
Guru
Posts: 1946
Joined: Tue Aug 10, 2010 9:16 pm
Location:

Re: Compression ratio and engine life

Post by peejay »

10:1 and 9-10psi boost on the car I am just walking out of. 250k miles and still runs like a top.

Some of the newer gasoline engines are way higher than that. 11:1 with 15psi on top, or 13-14:1 naturally aspirated.
Alaskaracer
Expert
Expert
Posts: 994
Joined: Sun Mar 21, 2010 9:48 pm
Location: Somewhere, Alaska
Contact:

Re: Compression ratio and engine life

Post by Alaskaracer »

ptuomov wrote: Thu Nov 30, 2017 6:35 pm Higher compression means higher cylinder pressures, both because of the higher compression directly and also because of faster burn around TDC. If the peak cylinder pressures are the limiting factor in reliability, then that’s an issue. For normally aspirated engines, it’s probably not an issue in many cases.
Not always. An engine sees two types of compression ratios. Static and dynamic. Static is nothing more than a difference in swept volume from bdc to tdc. Dynamic is what the engine sees while running and is affected by cam profile, cam timing, intake efficiency, and rpm. Higher static compression does not always mean higher cylinder pressure. As to engine life, it has pretty much zero effect on longevity.
Mark Goulette
Owner/Driver of the Livin' The Dream rear engine dragster
Speed kills but it's better than going slow!
http://www.livinthedreamracing.com
Authorized Amsoil Retailer
peejay
Guru
Guru
Posts: 1946
Joined: Tue Aug 10, 2010 9:16 pm
Location:

Re: Compression ratio and engine life

Post by peejay »

Coloradoracer wrote: Thu Nov 30, 2017 8:28 pm As to engine life, it has pretty much zero effect on longevity.

THIS.

Duty cycle is critical to engine longevity. Too much, and it wears out. Too little, and it basically dies of neglect. The happy medium is where you see the Methuselahs.
User avatar
ptuomov
Guru
Guru
Posts: 3587
Joined: Fri Aug 07, 2009 3:52 am
Location:

Re: Compression ratio and engine life

Post by ptuomov »

Coloradoracer wrote: Thu Nov 30, 2017 8:28 pm
ptuomov wrote: Thu Nov 30, 2017 6:35 pm Higher compression means higher cylinder pressures, both because of the higher compression directly and also because of faster burn around TDC. If the peak cylinder pressures are the limiting factor in reliability, then that’s an issue. For normally aspirated engines, it’s probably not an issue in many cases.
Not always. An engine sees two types of compression ratios. Static and dynamic. Static is nothing more than a difference in swept volume from bdc to tdc. Dynamic is what the engine sees while running and is affected by cam profile, cam timing, intake efficiency, and rpm. Higher static compression does not always mean higher cylinder pressure. As to engine life, it has pretty much zero effect on longevity.
Where did I say always?
Paradigms often shift without the clutch -- https://www.youtube.com/watch?v=cxn-LxwsrnU
https://www.instagram.com/ptuomov/
Put Search Keywords Here
PackardV8
Guru
Guru
Posts: 7619
Joined: Sun Jul 30, 2006 2:03 pm
Location: Spokane, WA

Re: Compression ratio and engine life

Post by PackardV8 »

Have been pondering what the expected life expectancy of an engine is when ever you increase the CR. I've always been under the understanding that the rings would take more of a beating but what about the bearings? Say you went from 10:1 up to 12:1,how about 10:1 to 15:1? is there any way to estimate the drop in life of engine(taking out factor of detonation),
As has already been stated, higher compression doesn't hurt anything. OEMs today are warranting 12:1 engines. But, as in your (), detonation kills, whatever the compression.
Jack Vines
Studebaker-Packard V8 Limited
Obsolete Engineering
digger
Guru
Guru
Posts: 2722
Joined: Sun Jan 27, 2008 6:39 am
Location:

Re: Compression ratio and engine life

Post by digger »

If I take a given engine and increase compression the temperature and pressure go up so do the loads and thermal stresses. It's extremely difficult to quantify what effect this have on life You won't find the answer here though as with everything it depends and why OEM spend millions trying to find out
user-23911

Re: Compression ratio and engine life

Post by user-23911 »

Higher compression = more detonation when tuned wrong= hammered bearings and blown head gaskets.




The important part is.......when tuned wrong.
Post Reply